Demogorgon Assembly Guide



View the Demogorgon spotlight here...
Check out the Demogorgon painting here...
You can find Demogorgon in our online store here...


With all resin models there is a small amount of preparation before painting can begin. For this you will need a few essential tools, glue and equipment to get you started.

Whether you have a dedicated room or are a kitchen table evening painter, you need to get comfortable. Painting figures does require many hours of sitting in the same position, so make sure your chair and table are the right height for you.


I recommend that you do not use a normal tungsten bulb as they cast a yellow light, but use a blue daylight hobby bulb. This gives a consistent bright colour balance over the whole table.

Hobby knife

This is the most important tool on your desk. You’ll need a knife with interchangeable blades as they dull quickly. My workhorse is the Swann & Morton scalpel with an extra wide handle. Another useful knife is an X-acto style, with interchangeable blades.

Side cutters and tweezers

What you are looking for, are the outside edge of the blades to be flush, producing a cleaner cut. These are good for snipping off unwanted resin parts.

Tweezers are handy for picking up and gluing small parts together.


Pin vice, drill bits and wire

Using a wire pin in a possible weak point of the model is the best way to strengthen the resin part. I use a 1mm drill bit with 0.9mm brass wire, which is available from any good hobby outlet.

Top Tip

If you are not sure of the exact position the figure will be in and you need some flexibility with the lines aligning correctly, use 1mm wire as usual for the pin and drill a 1.5 / 2mm hole the other end. The join will still be as strong and you have some movement for the final position.


Cutting mat

No-one needs knife marks in the kitchen table.


Gap Filling

With a multi-part miniature such as this, the resin pieces have shrunk at slightly different rates causing small gaps, this is normal with resin production and can be resolved with a little filling, and for this you will need a few different shaped tools and putty.


Preparing the miniatures

As part of the production process, the silicon mould which the resin is poured into has release agents in it, which are sometimes transferred onto the miniature. It is recommended that you wash the miniatures in warm, soapy water and they are completely dry, before starting any modelling.

All of these images are taken as I construct Demogorgon. Each stage is in order of how to build the miniature.

Side cutters are good at removing the larger feeds from the sprue. For the smaller feeds, I clip around the part and carefully cut the smaller feeds off with a sharp blade. Experience has showed me that there is a chance the clippers will snap any fine parts in the wrong place, as the resin flexes while clipping it.

To remove the mould-line from around the miniature, it is recommended to use a scalpel with a fresh blade.

Warped parts

This is an example from another model, but it can happen to any thin parts like a spear shaft or sword blade, have a tendency to warp in the moulding process as the vacuum is turned on. To fix this apply gentle heat from a hairdryer along the whole piece and the resin will move back to its original shape, molecular memory is a cool thing.


All the parts for Demogorgon have now been cleaned up with a scalpel and wet & dry paper, ready for the next process.


As this is a large model, I recommend gluing the columns on the base and painting it as a separate part, as it would be difficult to get the paintbrush into all the corners with the whole model complete.




The two halves are glued together to form the basis of the body construction.

Tail and legs

Inside the tail fitting is a small blob of extra resin, this was added so the fitting would cast properly, which means the opposite part will need to be trimmed to make a flush fit.

All the fittings on the Demogorgon have these square pegs which lock the parts in the correct place, because they are so large extra pinning is not really required, unless you want a very robust miniature.

Tentacle arms

As one of the tentacles is attached the column piece on the base, the left-handed arm comes in two parts, so it can be more animated.


Each head is two parts, which are glued together and then attached to the body.

Holding block

I recommend punning underneath the feet with a sturdy 2mm brass wire and attaching it to a scrap piece of wood, as this model is difficult to hold on its own and you don’t really want to cover it in fingerprints!


Gap filling

This is by far the most labour intensive task of the build but so worth it for a tidy finish.

Rolling out the putty into ‘rats-tails’ will make it easier to manage and apply it in small sections.

The two main constructed parts, primed and ready to paint.